TransLab Performance Transmissions LLC.

Local guy put a l*d and master kit in his car complains of slight whining after 300 miles. popped scha off and could see the stacked were drier than the golden girls and ashy as Chris rock in new jack city...

Noted oil in bellhousing which after a cloer look revealed the moon of death. cracked almost all the way around:(

Counter bearing not clipped into place this is what happens.

Opted to pickup a new donor and swap the L*D into it as the gewrset all the new masterkit he installed and the inner case were torched :(

I'm pretty slammed for the next couple weeks but will open the gates closer to July for the next round :)



translabperformance.net

4 goin out.

Larry Taylor's Liberty cased PPG dogbox with Speedfsctory SCHA in for an inspection put through the math.. an input shaft case bearing changed and ready for more.

Kevin Kaisers Super sick K20 VW Beetle had a dog 1 2 we put in it earlier and 3 4 SET. recently and LSzd was installed but Kevin decided it was time for fogs in 3 4 so a PPG outlaw NA dog upgrade was done and GEARXUSA 5th cuff installed.

A local mean ass Ministock cars trans came in to uncheatvthe L*D out of it...

And rounding out the weekends work is Marcos B track car unit we took a clutch L*D out of and put a helical in for atreet duty. This one also has the super short close 3 4 5 in it that uses a double synchro on 3 and 4 paired to a B16 1 2 and 4.8 final drive.

All buttoned up and ready. next round of guys lined up.

staying busy. Hit me up :)

As normal translabperformance.net is up and hummin.

GEARXUSA GEARSETS AND FINALS
PPG B and K stuffs

All tarsnalab 5 and 6 cuffs for k and b fwd and awd in stock.

billet vc mounts and awd block off plates.

Input shaft thrust tools as well.

Holler and thanknyou guys as always

❤️🧡💛💚💙

Andre brought in his GEARXUSA Outlaw AWD dogbox for an inspection as iylt only had a few passes on it after we changed 2nd and a 1 2 slider after a strain setting issue.

Stated a low RPM growl... So as he planned on beating on it this weekend he did want anyone with 15k invested in a gearbox should do.

took it out and inspected it. This car 1.3 60 foots and has 50 pass on this gearset.

All we found wrong was the input shaft bearing was super chunky.

Had him bring it up to daddy for a look see changed the bearing out and he's ready to rip this weekend :)

Always a good time.with good people

Appreciate you my man

Volvo power steering install done now that lines are complete... Front end complete.

Waiting for the brake stuff to show up to start lines to back off car and pass through ebrake setup... So this weekend I'll get the car cleaned up inside and pedals in it to finish that off.

I need to degree the damn cams in the motor so I can get the motor and trans innthe car lol.

Stuck the intercooler on her to see if i had to paint more than the face black for visibility... or lack of it ;)

But just the face is plenty so well get her off tape her up and make it dissappear :)

4 Day weekend son ope to get a full day one of them onnit... But the Nova needs one too and she's been neglected too long

Kevin's JDM AWD CRV k trans in and out for Gen2 Drag 2 kit, L*D, GEARXUSA 4.4 FINAL Master kit and Springs throughout.

IMACULATE core care of ... Man this thing was a pleasure to work on. Impeccable. The re-zinced hardware and blasted cases... chefs kiss.

Pluggin away and opened up scheduling but pretty booked out again. Pluggin away on the as well.

Translabperformance.net is hummin along per the norm.

Billet transfer block off plates
K B and H 5th and 6th cuffs
Billet wago vc mounts
input thrust tools
CSS blockoffs
Driveshaft slip joints
Billet cupholders
Dogboxes
Final drives
L*Ds
SYNCHRO KITS AND MORE !!!

translab gearx ppg speedfactory syp MFactory Synchrotec BFGEARUSA and more all on deck.

hit up the site and use code FREESHIP at checkout to save on the ride

Pushed ol girl outside to get a look and check that I got close on the rear alignment after remembering how I had it setup during mock up and fab..

Hoping tonget Cole over here with some toe plates to get close on the front aftwr the new rack and tiebrod ends 🙏

Installed the TPU engine bay plugs and radiator mount inserts i made..

It looks amazing.

need to clean it up inside so Ican get the pedals in it and get the brakes in progress. Front calipers are loaded and waiting on seats.

Refurbished the cowl cover and rubber hood seal offbthe parts car and layed wm onnthe car for now since ain't no point fastening till hoods on and im gonna leave it off as log as I can

The new door panels off the parts car look great!

Gettin there!