Skip to content
FindGlocal
Engine Pro

Engine Pro

198 Industrial Park Road, Denver Automotive wholesaler

Nation's leading engine parts distributor, featuring name brand engine parts and custom engine kits sold by professional rebuilders.

11/03/2026

đź”§ A quick alignment check could help prevent costly problems down the road.

The transmission mounting surface and timing cover should align with the crankshaft centerline, but this check is often overlooked. Misalignment can contribute to pump, converter, crank thrust, seal, and timing cover issues.

Ron Flood of Cedar Machine checks alignment using a precision bar, main bore rings, and a magnetic-base dial indicator. It’s also easy to sweep the surface on a line-boring machine with the boring bar locked in place.

Do you check these surfaces as part of your machining process? Share your approach in the comments. 👇

Have a shop tip of your own? Share it with us at enginepro.com/submit-a-tip/

10/26/2026

For my spray washer, I mix a 20-gallon barrel of rinse water with ½ teaspoon bleach and a capful of cooling system corrosion inhibitor. I pull it through a media-blasting gun siphon tube straight from the tank.

Why I use it: this cool blend helps prevent flash rusting after rinsing—way better than cold water alone. I also use the same mix in my dyno bulk tank to keep the engine cooling system water jacket from rusting and to help the water system stay cleaner longer.

And yes—I haven’t noticed any negative effects in my setup.

Shared by Ron Flood | Cedar Machine (North Branch, MN).

Have a shop tip of your own? Share it with us at enginepro.com/submit-a-tip/

10/19/2026

đź”§ CAM LOBE TAPER: DETAILS MATTER!

Randy Torvinen checks every new flat-tappet camshaft for proper lobe taper using a precision indicator. He’s found cams with less than .0005" of taper, including two in the same order that had to be returned for correction.

The lesson? Measure before you install. Catching small problems early can prevent bigger headaches later!

👏 Shop wisdom courtesy of Randy Torvinen, Torvinen’s Machine, Menahga, MN.

Have a shop tip of your own? Share it with us at enginepro.com/submit-a-tip/

10/09/2026

Let's try this again with the right photo!!!

Need an easier way to keep brake cleaner and pump oil cans within arm’s reach in the shop? 🔧

A handy 3" PVC holder fits with a simple mount—just attach a cut 45° piece to your machine with one screw for quick grab-and-go storage. For aerosol cans, a few screws in the bottom keep everything in place.

Proudly shared by Adney Brown | Performance Crankshaft Inc. (Ferndale, MI).

Have a shop tip of your own? Share it with us at enginepro.com/submit-a-tip/

09/28/2026

Boring tips that save time and prevent expensive mistakes đź”§âś…

Different boring bar bit styles can cut different sizes, depending on where the cutting tip is tangent to the bar centerline. Testing found a .007" difference between standard style bits and indexable bits.

Best practice:
âś… Calibrate the micrometer to the bit that cuts the largest
âś… Then adjust the other bits using the differential

That approach makes it extremely difficult to cut an oversize bore—worst case, simply add the differential and recut.

If you have a shop tip to share, submit it at enginepro.com/submit-a-tip/

09/21/2026

Bead blasting tip that saves time (and screens) 🔧✨

I always drop a 10-gauge sheet metal plate into my bead blaster. It helps heavy parts slide more easily and takes the wear instead of the screen. Cleaner blasting with less hassle.

If you have a shop tip to share, submit it at enginepro.com/submit-a-tip/

09/14/2026

Resizing Pontiac rods is easier with the right setup 🔧⚙️

When the pin boss is wider than the big end, you usually have to lift the rod to use the Delta Grinder.

A simple CK10 big-end spacer makes the job quick, repeatable, and accurate. Share your tip with us at enginepro.com/submit-a-tip/

09/09/2026

Fall may be your slower season—but it doesn’t have to be wasted time. 🍂🔧
Use this downtime to review your last jobs: compare estimates to actual labor, machine time, tooling, parts margins, outside services, and delivery costs.

Then:
âś… tighten parts margins
âś… update pricing
✅ reach out to customers you haven’t heard from
âś… refresh your website and social media
âś… build your pipeline for the busy months ahead

Make fall count.

08/31/2026

Quick tip for crank grinding wheel balancing: sometimes it’s faster to add a small rare-earth magnet to the wheel, mark the spot, and tweak from there—rather than constantly moving weight to chase the exact balance. Small changes, big accuracy. 🔧⚙️

08/26/2026

Installed flanged sleeves with just a boring bar, chain hoist, and magnetic dial indicator. Simple setup—super accurate results! 🔧🙌

Other Automotive Wholesalers in Denver

Show All
  • Xglass

    Xglass

    Denver

    Remplazo de vidrios automotrices!� Instalation a domicilio Damos servicio a toda el área metropolitana de Denver para cotizaciones llame al 720-579-3293 trabajo de buena calidad y...

  • McGee Company

    McGee Company

    1140 S Jason Street, Denver 80223

    Since 1951, a family owned business focused on tire service shop equipment, supplies, & retreading.

  • Americanmusleexports

    Americanmusleexports

    1380 S Osage Street, Denver 80223

    Export of American muscle cars, classic cars and trucks to New Zealand and Australia. Direct from the US. Doesn't matter how old or new we'll find it.

  • reparaciĂłn de cristales automotrices

  • AVG Towing is a local towing company providing fast and reliable service. Whether you need roadside assistance or vehicle transport, we’re here to help 24/7! 📍 Serving Denver Metr...

Alerts

Be the first to know and let us send you an email when Engine Pro posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Subscribe

We will notify you when anything happens in Denver.