Engr. Adnan Rasheed

https://youtu.be/LVM7G6ivyBY

Determine the factor of safety against yielding | Problem 10-89 | Mechanics of materials 10–89. The gas tank has an inner diameter of 1.50 m and a wall thickness of 25 mm. If it is made from A-36 steel and the tank is pressured to 5 MPa, Deter...

Problems about Failure theories, Mechanics of materials RC Hibbeler

10-90 | Determine required minimum wall thickness | Tresca criteria | Mechanics of Materials 10-90 The gas tank is made from A-36 steel and has an inner diameter of 1.50 m. If the tank is designed to withstand a pressure of 5 MPa, determine the requ...

https://youtu.be/9oUca4VP8TE

10-85 | Determine the smallest yield stress for a steel #maximumshearstresstheory 10–85. The state of stress acting at a critical point on a machine element is shown in the figure. Determine the smallest yield stress for a steel that might...

https://youtu.be/lkPcA5jZoT4

The Shocking Truth About Torque T and Maximum Shear Stress Theory In this video we are going to talk about The Shocking Truth About Torque T and Maximum Shear Stress Theory10–92. The shaft consists of a solid segment AB a...

https://youtu.be/z0DRoUWCgoI

Understanding Failure theories problems | Failure Theories | Engr. Adnan Rasheed Mechanical In this video you will be Understanding Failure theories problems or Failure Theories. Engr. Adnan Rasheed Mechanical10–75. The components of plane stess ...

https://youtu.be/stkUp9PZYNU

Draw the shear and moment diagrams for the beam | Ex 6.6 | Bending | Mechanics of Materials RC Hib Example 6.6 Draw the shear and moment diagrams for the beam shown in Fig. 6-12a. Dear Viewer You can find more videos in the link given below to learn moreTh...

https://youtu.be/gJUe1uPkdxY?si=X3ZAkPPdp1B1Otwq

Draw the shear and moment diagrams for the beam | Ex 6.5 | Bending | Mechanics of Materials RC Hib Example 6.5 Draw the shear and moment diagrams for the beam shown in Fig. 6-11a. Dear Viewer You can find more videos in the link given below to learn moreTh...

https://youtu.be/fjyiK_oWTM8

4.111| Determine the largest offset that can be used | Mechanics of materials Beer and Johnston 4.111 An offset h must be introduced into a solid circular rod of diameter d. Knowing that the maximum stress after the offset is introduced must not exceed ...

https://youtu.be/-QS8i9nXrrQ

4.107 | Determine the maximum stress in post | Bending | Mechanics of Materials Beer and Johnston 4.107 The four forces shown are applied to a rigid plate supported by a solid steel post of radius a. Knowing that P 5 100 kN and a = 40 mm, determine the ma...

https://www.facebook.com/share/p/19CE5Bp6Gp/

Bending-Moment Diagrams Made Simple | Mechanics of Materials Beer and Johnston Dear Viewer You can find more videos in the link given below to learn more Theory Video Lecture of Mechanics of Materials by Beer & Johnstonhttps://youtube.c...

https://youtu.be/ZHQQn5rA6sc

4-30 | Determine the resisting bearing force F for equilibrium | Mechanics of Materials RC Hibbeler 4–30. The weight of the kentledge exert an axial force of P= 1500 kN on the 300-mm diameter high-strength concrete bore pile. If the distribution of the res...

https://youtu.be/rG3MVTuJseE

5.50 | Determine the equations of the shear and bending-moment curves | Mechanics of Materials 5.50 For the beam and loading shown, determine the equations of the shear and bending-moment curves and the maximum absolute value of the bending moment in t...