Manufacturer and Exporters of Sugar plant machinery/ Jaggery plant machinery and a specialised manuf The farmers transport the cane stalks (i.e.
We are a leading manufacturer and Exporters of complete sugar plant and machinery.We design and manufacture the complete mill according to one's own crushing need.Our complete range of products are- Cane carrier,Cane kicker(cutter),Cane Fibriser,Crushing mill with gear box,Rake type or slat type inter carrier,GRPF & TRPF,Bagasse carrier,Crystallizers, Centrifuges, Boiling house equipments like- Ev
aporating pan, Juice heater,Concentrator, Juice Clarifier,Chokeless pump, Juice pump, Air blower etc. Our genaral sizes of the mill are- 11x14, 13x18, 16x24, 18x30, 20x30, 18x36, 24x36, 20x40, 24x48, 25x50 (All these sizes are in inches). And the capacity of our sugar plants starts from 50 TCD and goes upto 2000 TCD. For more information please log on to www.diamondengineeringworks.com
or mail me at [email protected]
or [email protected]
Process of manufacturing of sugar from sugarcane :
1. Juice extraction from cane
Sugar cane :
The cane plant consists of a stalk, roots, growing leaves, the remains of dead leaves, and a growing leafy top. The typical composition of cane is as follows:
15% dissolved matter (13% sucrose; 2% are other sugars -mainly glucose and fructose)
15% fibre (insoluble), and 70% water. For every 100 Ton cane crushed, 30 Ton of fibrous residue (bagasse), and about 12 Ton sugar and 4 Ton molasses are made. cane without roots, without leaves and without tops) to the sugar mill in specially designed vehicles that facilitate easy loading and offloading. Cane preparation:
Juice can be removed from cane either by repeated crushing and washing (milling) or by washing alone, with a final squeezing simply to dry the spent fibre (diffusion). Better sucrose extraction can be obtained by crushing finely shredded cane rather than intact stalks and “Preparation” refers to that step in which cane is finely shredded before juice is extracted either by milling or diffusion. Cane is prepared by passing it through one or two sets of cane knives and then through a shredder. Milling:
A basic cane mill consists of three grooved rollers. Prepared cane is squeezed between the rollers, thus forcing the juice out of the fibre. The basic work of a mill is the separation of juice from fibre. Fibre, however, has the natural property of always retaining approximately its own weight of juice regardless of the pressure applied to it. To displace retained juice, water is poured onto the cane fibre before crushing. This is called imbibition. A single milling unit would give an unacceptably low extraction. Typically, five mills are set in tandem and cane is passed in series from Mill 1 to Mill 5. Diffusion:
A diffuser is an enclosed carrier through which a bed of prepared cane is slowly dragged, while copious quantities of water and juice percolate through the bed to wash out the sucrose -bearing juice. The fibre leaving the diffuser is saturated with liquid and has to be dewatered in a mill before being sent either to the boilers or to by-product processes. Purification of juice:
Juice from a milling tandem contains a large amount of cane fibre that falls out with the juice between the rollers of the mills. To remove the fibre, juice is poured over a wire-mesh screen, or cascaded over an inclined wedge-wire screen.Diffuser juice, because of the screening effect of the cane bed itself, is generally not screened. The juice is heated and lime is added to neutralise the natural acidity. It is then placed in a large settling tank called a clarifier The purpose of clarification is to produce a clear juice that is light in colour and free of suspended matter. To improve the precipitate formation, flocculent is added. The settled precipitate, referred to as mud, is pumped out of the trays of the clarifier and sent to the filtration station where the juice it contains will be recovered. If a diffuser is used, it is sent to the diffuser and filtered through the bed of bagasse.
2. Crystal growth:
Evaporation:
Before crystal growth can take place the clear juice must be concentrated to syrup by the removal of water by evaporation. To improve the efficiency of the water removal step a process known as multiple effect evaporation is used. Multiple effect evaporation is the scheme where juice is boiled in series in several vessels, with steam fed to vessel 1 only. Vapour from vessel 1 boils the juice in vessel 2, vapour from 2 boils the juice in 3, and so on until vapour from the final vessel goes to waste. Sugar boiling:
The syrup produced by the evaporators is concentrated further in specially designed vessels known as pans. As the concentration rises the dissolved sugar crystallises and the work of the pans is to grow sugar crystals (from the sucrose in syrup) in several steps to maximise the amount of sucrose recovered in raw sugar. This is typically done in three boiling steps; each step producing, after crystal/molasses separation, A-sugar and A-molasses, B-sugar and B-molasses, and C-sugar and C-molasses or final molasses. Supersaturation is the "driving force" in all sugar boiling. Supersaturation is controlled by adding water or syrup to massecuite (crystal / molasses mixture) and by controlling the temperature. When the massecuite is discharged from the pans it is retained in stirred tanks called crystallisers, where the sugar crystals continue to grow through cooling rather than boiling. Separation of crystals from molasses:
Massecuite leaving the crystallisers has now to be separated into crystals and molasses. The more efficient this separation, the more sucrose will be recovered as sugar and the less sucrose will be lost in molasses. A centrifugal is a machine that separates crystals from molasses. Centrifugation involves spinning massecuite in a perforated basket; centrifugal force acts on the molasses, forcing it through the perforations while the sugar remains on the basket wall. Water and steam may then be sprayed onto the crystals to wash off the remaining molasses. Sugar drying:
Sugar leaving the centrifugals has excess moisture which has an extremely detrimental effect on the keeping quality of the raw sugar and drying is therefore important. In a drier, the moisture is driven off from the surface of the liquor layer covering the crystal by passing heated air around the sugar crystals. The product from the process described so far is a raw sugar (Brown sugar) that can be used as is, or sent to a refinery to be converted to a white (refined) sugar. Sugar refining:
The purpose of the refinery is to remove impurities from sugar crystals. The refinery accepts raw sugar as its feed material. The sugar is dissolved (melted) and the colour is removed by various clarification processes. Re-crystallisation (from a higher purity mother liquor) is alone responsible for a considerable amount of colour removal but other techniques must be employed to obtain the low colour levels of white sugar. Tongaat Hulett uses two colour removal processes before the crystallisation and these are carbonatation and ion exchange. In carbonatation lime and CO2 (carbon dioxide) gas are added to the melt to form a calcium carbonate precipitate. This precipitate absorbs colour, is removed by filtration. Further colour is then removed by ion exchange. Resin beads are held in tanks through which the liquor is allowed to percolate under pressure. The purified melt is evaporated and up to 4 crops of crystals are boiled from this. These crystals are combined to form the refined sugar product.
