Back2Basics Lab
Share
Contact information, map and directions, contact form, opening hours, services, ratings, photos, videos and announcements from Back2Basics Lab, Computer training school, III/36F3, JJ NAGAR, Opp to Govt College of Engineering,. G. MADEPALLI, Bargur, Krishnagiri.
Back2Basics Lab is an industry-aligned online PCB design training program that bridges the gap between academics and real-world skills through hands-on virtual labs and mentorship.
05/10/2026
12V signal, but the ADC needs a safe lower voltage. ⚡
A voltage divider scales 12V down to 4V for the MCU ADC.
Want to learn PCB design?
🎁 DM us to get your FREE PCB Design Course.
02/10/2026
Why does a 2V LED need a 300Ω resistor on a 5V supply? 💡⚡
A small resistor makes a big difference — it keeps the LED current safe.
Want to learn more practical electronics? DM us for a FREE demo course.
02/10/2026
PWM switches fast, but the duty cycle controls the average output. ⚡
In this example, 60% duty cycle at 5V gives a 3V average output.
Want to learn more about electronics?
🎁 DM us to get your FREE PCB Design Course.
01/10/2026
Your sensor sends 7V, but your MCU can only handle 5V. ⚠️
What would you choose to make the input safe?
A, B or C? 👇
🎁 DM us to get your FREE PCB Design Course.
01/10/2026
MOSFET turns OFF… but the coil doesn’t stop instantly. ⚡
The stored energy can create a dangerous voltage spike.
Can you pick the right protection?
A, B or C? 👇
🎁 Get your FREE PCB Design Course — DM us now.
30/09/2026
The MOSFET turns OFF… but the coil still has energy ⚡
That stored energy creates a voltage spike.
A flyback diode gives the current a safe path and protects the switching device.
🎁 Get your FREE PCB Design Course — DM us now.
30/09/2026
Why does a MOSFET gate resistor slow down switching? ⚡
A gate resistor controls the charging current of the MOSFET gate.
Higher resistance → Lower gate current → Slower switching.
Want to learn PCB Design & Embedded Systems? 👇
🎁 Get your FREE PCB Design Course — DM us now.
29/09/2026
Your button is OFF… so why is the MCU reading random values? 🤔
Can you find the correct fix?
A, B or C? 👇
🎁 Get your FREE PCB Design Course — DM us now.
29/09/2026
A MOSFET gate should never be left floating. ⚡
A 10kΩ pull-down resistor gives the gate a defined LOW state during reset, startup, or when the MCU output is disconnected.
In this example:
5V / 10kΩ = 0.5mA
Simple component. Important job.
It helps prevent unwanted MOSFET switching and keeps the circuit behavior predictable.
DM us to get a free demo course.
28/09/2026
A fast current spike can pull an MCU’s supply voltage down in an instant. ⚡
A local decoupling capacitor supplies charge right where the MCU needs it.
In this example:
Minimum calculated capacitance = 8nF
Practical choice = 100nF
That’s why a 100nF ceramic capacitor close to the VCC pin is such a common design choice.
Small capacitor. Big difference in supply stability.
DM us to get a free demo course.
Category
Address
III/36F3, JJ NAGAR, Opp To Govt College Of Engineering,. G. MADEPALLI, Bargur
Krishnagiri
635104
Alerts
Be the first to know and let us send you an email when Back2Basics Lab posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.