Sub Engr Test Preparation
Share
All Previous PPSc ; NTs Mcqs Test Preparation
14/09/2021
Dated 13-09-2021
2nd Year
M.O.S chp #8
P.Health chp #9,10
Test.......
1).Quantity of water required for one person per day is called.......
a) Required water
b) Demand of water✓
c) yield
d) All of these
2).Demand of water depend upon.......
a) weather
b) habits of people
c) quality of water
d) all of these✓
3).Quantity of water "Q" required for fire fighting according to kuichling formula...
a) 3180√P✓
b) VxA
c) 3150(P/5)
d) 3860√P
4).Average daily demand per person "q" for population "P" while "Q" quantity of water supplied in the whole the year will be...
a) Q/365p✓
b) 365p/Q
c) PxQ/365
d) 365/PxQ
5).In one liter simple of water salt is 100 mg in PPM it will be.......
a) 10
b) 100✓
c) 1000
d) 10000
6).WHO recommended maximum amount of florides in drinking water in PPM...
a) 0.2
b) 2.0
c) 4.0✓
d) 10
7).WHO recommended maximum total dissolved solids in drinking water in PPM....
a) 500
b) 1000
c) 1500✓
d) 2000
8).Colour of water is tested by ....
a) pH scale
b) Threshold No.✓
c) Cobalt No.
d) PPM
9).Tinto meter instrument is used to measure ......of water.
a) pH
b) Acidity
c) Turbidity
d) Colour✓
10).Recommended pH value of potable water( for drinking and cooking) is....
a) 6.5--8.5
b) 7--8.5
c) 8--9.5✓
d) 9--11
11).B.coli index of drinking water...
a) less than 3✓
b) 3--5
c) 5--10
d) 10--15
MOS
12).Moment area method is used to determine...
a) slope and deflection✓
b) S.F and B.M
c) Tensile stress
d) compressive stress
13).Value of maximum deflection that acts at a point of cantilever...
a) fixed end
b) free end✓
c) middle
d) both ends
14).Value of deflection at the ends of a simply supported beam..
a) maximum
b) minimum
c) zero✓
d) average
15).The value of slope at maximum deflection of beam is...
a) zero✓
b) minimum
c) maximum
d) none of these
16).Resistance against deflection of beams...
a) hardness
b) stiffness✓
c) toughness
d) brittleness
17).Deflection of beam is directly proportional to...
a) Load✓
b) youngs modulus
c) section modulus
d) moment of inertia
18).Deflection in beams is inversly proportional to.......
a) load
b) span
c) m.o.i✓
d) both a,b
19).Deflection of beam may be reduced by....
a) decreasing the depth
b) increasing the span
c) decreasing the breadth
d) increasing the stiffness✓
20).The value of slope at maximum deflection of beam is......
a) zero✓
b) maximum
c) minimum
d) none of these
21).The stiffness of beam increases with the increase of...
a) inertia
b) youngs modulus
c) loads
d) both a,b
Goood Luck....
10/09/2021
Test........
M.O.S
1).Bending stress at neutral axis of beam...
a) maximum tensile
b) maximum compressive
c) zero√
d) negative
2).Strength of a beam is directly proportional to...
a) section modulus
b) bulk modulus
c) shear modulus
d) all of these√
3).A beam of uniform strength has its same value at every cross section....
a) B.M
b) bending stress
c) deflection
d) stiffness√
4).Bending equation is...
a) M/f=I/y=E/R
b) i/g=f/r=cb/e
c) M/I=f/y=E/R√
d) none of these
5).The unit of modulus of section is...
a) kg-m2
b) m3 or cm3√
c) m2 or cm2
d) m4 or cm4
6).Modulus of section of a square beam...
a) D4/6
b) D4/12
c) D3/12
d) D3/6√
7).In beam section bending stress varies...
a) Linearly √
b) Parabolically
c) Elliptically
d) Hyperbolically
8).The stress caused by bending moment is called...
a) shear stress
b) bending stress√
c) normal stress
d) tensile stress
Public health
9).Conveyance of water safely according to demand is called....
a) plumbing
b) pipe fitting
c) water supply√
d) all of these
10).Gas used for disinfection the water supply.....
a) hydrogen
b) carbon dioxide
c) chlorine√
d) all of these
11).Mostly used pipe for water supply now a days.
a) cast iron
b) G.i
c) PPRC√
d) asbestos
Survey
12).GPS is used to observe....
a) magnatic bearing
b) true bearing
c) absolute location
d) all of these√
13).True coordinate can be observe with
a) G.p.s√
b) total station
c) compass
d) theodolite
14).Set up and position of sun and moon can be determined in this mode of GPS.....
a) menu mode√
b) location mode
c) map mode
d) trip mode
15).Record of speed of vehicle and time consumed during travelling can be determined in this mode of GPS....
a) compass mode√
b) menu mode
c) map mode
d) location mode
16).Find settelite position and signal power in this mode of GPS....
a) location mode√
b) menu mode
c) map mode
d) trip mode
Goood Luck....
Test......
Public Health Tech
1).Providing different services in building is called........
a) Pipe fitting
b) Plumbing√
c) Engineering
d) Servicing
2).Word G.i stands for...
a) Globle influence
b) Galvanized iron√
c) Germ infection
d) Golden ink
3).Bell and spigot end joint is used in the case of such pipes....
a) Concrete √
b) Asbestos
c) Steel
d) G.i
4).Standard available length of PPRC pipe is....
a) 8'
b) 13'√
c) 16'
d) 20'
5).Measuring unit of G.i pipe is....
a) Length√
b) Breadth
c) Height
d) None of these
6).PPRC stand for.....
a) Plymer profile random copolymer
b) Polyprepylene random copolymer√
c) Poly per random copo
d) All of these
Survey.
7).The function of theodolite is to measure.
a) Horizontal angle
b) Vertical angle
c) Deflection angle
d) All of these√
8).The size of theodolite is expressed by....
a) Dia of main scale√
b) Length of telescope
c) weight of theodolite
d) Magnifying power
9).The axis of rotation of telescope in the horizontal plane is called
a) Horizontal axis
b) Vertical axis√
c) Trunion axis
d) None of these
10).Reticles of a telescope are cleared with....
a) Foot screw
b) Object glass
c) Eye piece√
d) Focusing screw
11).Function of optical plummet of theodolite..
a) Centering√
b) Sighting
c) Set in case
d) None of these
12).Latitude is determined by the formula.......
a) L sin@
b) L cos@√
c) L/sin@
d) L/cos@
13).The theodolite whose telescope can rotate through complete revolution in vertical plane is called....
a) Non transit
b) Transit√
c) Tilting
d) All of these
14).Rotating telescope of theodolite through 180° in vertical plane is called.
a) Rotating
b) Transiting√
c) Centering
d) Swinging
15).The formula to calculate the departure of a survey line is....
a) L sin@√
b) L cos@
c) L tan@
d) L/sin@
16).In Gales table all point of traverse are brought in the quadrant....
a) 1st√
b) 2nd
c) 3rd
d) 4th
17).Algebric sum of internal angles of four sided closed traverse is..
a) 540
b) 360√
c) 280
d) 90
18).Latitude and departure are both negative in the quadrant....
a) SE
b) NE
c) SW√
d) NW
M.O.S
19).Centre of solid geometrical object is called.....
a) Centre
b) Centriod√
c) Centre of gravity
d) Central axis
20).Density of water in M.K.S system......
a) 1000 kg/m3√
b) 9.81 KN/m3
c) 62.4 lb/ft3
d) 1g/cc
21).The distance of c.g from base of a triangle of height 'h'.......
a) h/2
b) h/3√
c) h/4
d) 2h/3
22).The distance of c.g from vertex of a triangle of height 'h'......
a) h/2
b) h/3
c) h/4
d) 2h/3√
23).A isoceless triangle base is 6 c.m and height is 9 c.m find its centre...
a) 3,2
b) 3,3√
c) 3,4
d) 4,4
24).Centriod of quarter circle lies at a distance of....
a) D/2
b) 4R/3π√
c) 3R/4π
d) 5R/3π
25).A detail study of forces and their effect structure/object along with some suitable protective measures for safe working condition is known as....
a) Mechanics√
b) Moment of inertia
c) Centriod
d) None of these
Gooood Luckkkkk
Test.......
1st Year.
Construction.
Full book.
New book 2021.
1).The main function of alumina in brick earth is to impart.......
a) Plasticity💚
b) Increasing volume
c) Colour
d) Strength
2).The following ingredient exclude in white cement.......
a) iron oxide💚
b) tri calcium
c) alumina
d) silica
3) The slump test of concrete is used to measure its.........
a) workability strength💚
b) pre stressed
c) Batching
d) mixing
4) When a heavy structure is to be constructed in sandy soil the foundation used as...
a) Pier foundation💚
b) strap foundation
c) Raft foundation
d) none of these
5).Raft foundation is also known as.......
a) pile foundation
b) pier foundation
c) Cantilever foundation
d) Mat foundation💚
6).A horizontal layer of bricks laid in mortar is known as.........
a) Course💚
b) Stretcher
c) header
d) closer
7).The minimum bearing of lintel on door or window is kept........
a) 100mm (4")💚
b) 150mm (6")
c) 200mm (8")
d) 250mm (10")
8).An inclined member of a roof truss........
a) Rafter💚
b) purlin
c) cleat
d) none of these
9).The best type of pointing in ordinary cases........
a) Flush pointing💚
b) deep struck pointing
c) tuck pointing
d) recessed pointing
10).The temporary support provided to an unsafe structure is called...........
a) Shoring💚
b) under pining
c) proping
d) timbering
Goooood Luck
First Year
Engineering Drawing.1
Full Book Chp(1-12)
Total MCQS (50)
1).Pencil used for free hand sketching.....
a) soft✅
b) hard
c) heavy
d) none
2).Which is solid geometrical figure...
a) square
b) rectangle
c) cone✅
d) triangle
3).The scale 1"=15' in R.F will be...
a) 1/120
b) 1/180✅
c) 1/150
d) 1/130
4).The height of letter using for main title is
a) 1/2"✅
b) 1/3"
c) 1/4"
d) 1/7"
5).The lower most line used for lettering is called....
a) cap line
b) waist line
c) base line
d) drop line✅
6).Object line is also called.......
a) Dotted line
b) center line
c) out line✅
d) Hidden line
7).The thickness of object line is.......
a) 0.3 mm
b) 0.4 mm
c) 0.5 mm✅
d) 0.6 mm
8).Tri hederal angles make such right angles...
a) 8✅
b) 6
c) 4
d) 10
9). Di hederal angles make such right angles...
a) 8
b) 6
c) 4✅
d) 10
10).Revolved section section is also called...
a) half section
b) full section
c) partial section
d) Rolled section✅
11). Broken section is also called......
a) Half section
b) full section
c) rolled section
d) partial section✅
12).A system of dimension in which single direction is adopted........
a) unidirectional✅
b) Aligned
c) base line
d) bi directional
13).A system of dimension in which dual direction is adopted...
a) unidirectional
b) aligned✅
c) base line
d) bidirectional
14).A drawing having length,breadth,depth in one view is called as...
a) cylinder figure
b) plane figure
c) cone
d) pictorial✅
15).The view drawn by isometric scale is...
a) pictorial
b) perspective view
c) isometric projection✅
d) orthographic projection
16).True shape of object are shown with the help of....
a) oblique view
b) section view
c) auxiliary view✅
d) none
17).we get the detail information in auxiliary view...
a) inclined✅
b) horizontal
c) vertical
d) none
18). A cone is a such type of surface...
a) single curve✅
b) double curve
c) both
d) none
19). A Sphere is a such type of surface....
a) single curve
b) double curve✅
c) both
d) none
20).Minimum size of kitchen....
a) 4 sqm✅
b) 3 sqm
c) 2 sqm
d) 5 sqm
21).Height of the plinth for the residential building normally is....
a) 1' /30 c.m
b) 1.5' / 45 c.m✅
c) 2' / 60 c.m
d) 2.5' / 75 c.m
22).stairs and stores are located in the direction...
a) south
b) north✅
c) east
d) west
24).ideal location of kitchen in the house is...
a) north
b) south
c) west✅
d) east
25).a figure having area but no thickness is called as.
a) plane figure✅
b) solid figure
c) prism
d) pyramid
26).The ratio between orignal size and size on drawing sheet...
a) scale✅
b) plain scale
c) diagonal
d) scale card
27).The upper most line used for lettering...
a) cap line✅
b) waist line
c) base line
d) drop line
28).what are the simple geometrical figure..
a) two dimension✅
b) three dimension
c) multi dimension
d) none of these
29).knowledge for the internal detail after cutting plane line for a body is termed as...
a) Dimensioning
b) sectioning
c) projectioning
d) all of these✅
30).view of orthographic projections is....
a) top view
b) front view
c) side view
d) all of these✅
31).isometric scale is near......% of normal scale....
a) 62.5
b) 67.5
c) 80✅
d) 100
32).Element of dimensioning....
a) dimension line✅
b) extension line
c) leader line
d) all of these
33).A view showing full size of an inclined surface of an object...
a) front view
b) top view
c) side view
d) auxiliary view✅
34).Name of the drawing in which object opened and spread on smooth surface.....
a) rotation
b) progression
c) development✅
d) all of these
35).A plan showing thickness of wall by single line...
a) line plan✅
b) detail plan
c) site plan
d) foundation plan
36).Drawing showing size of rooms,location of door and thickness of walls.....
a) line plan
b) detail plan✅
c) site plan
d) foundation plan
37).The arrangment of rooms in a building with respect to sun and air
a) planning
b) ventilation✅
c) orientation
d) air conditioning
38).ideal location of bedroom in the house is..
a) north
b) south
c) east
d) west✅
39.) Presentation of ideas by means of sketch....
a) view
b) brain
c) drafting✅
d) skeleton
40).Writing on drawing sheet is called....
a) Lettering✅
b) Numbering
c) Writing
d) Sketching
41).A set of construction or working drawings that define all the construction specification of a residential house such as dimensions,materials,layouts,installation methods and techniques.
a) House planning✅
b) Orientation
c) Ventilation
d) none of these
42).Top level of window should be...
a) 7'
b) 6'
c) Bottom level of door
d) Top level of door✅
43).A view parallel to inclined surface is called.
a) Plan
b) Elevation
c) Site plan
d) Auxiliary view✅
44).The type of dimension in which shows the length,breadth,and height of the body....
a) Size dimension✅
b) Location dimension
c) Direct dimension
d) None of these
45).Which type of the line is drawn to show the invisible part of body?
a) Dotted line
b) Cutting plane line✅
c) Hidden line
d) Centre line
46).A section in which details are shown with dotted line....
a) Revolved section
b) Phantom section✅
c) Offset section
d) None of these
47).A section shown separately in large size..
a) Detail section
b) Revolved section✅
c) Offset section
d) Auxiliary section
48).A surface having length and breadth is called....
a) Plane ✅
b) Solid
c) Principal plane
d) Profile plane
49).A point which measurment have no any importance...
a) Line
b) Point✅
c) Circle
d) Polygon
50).Instrument used to draw curves...
a) Compass✅
b) Protector
c) Scale
d) All of these
(End)
Goooood Luckkkkk
Test..........
1st Year.
Construction.
Full Book Chp #(1-23)
Total MCQS (125).
1).Red colour of bricks depend upon....
a) iron oxide✔️
b) alumina
c) burning
d) none
2).silica is also called....
a) alumina
b) silt
c) sand✔️
d) none
3).Granite is an Example of....
a) silicious stone✔️
b) argalicious stone
c) carcalious stone
d) none
4). Quick lime is also known as.....
a) Fat lime
b) hydraulic
c) calcinated✔️
d) slaked
5).The following lime used in massonary and plaster work......
a) fat lime
b) lean lime✔️
c) hydraulic lime
d) all of these
6).Gypsum is added to cement at the time of manufacturing is.....
a) increase setting time✔️
b) decrease setting time
c) increase strength
d) decrease strength
7).Early strength of cement take place due to.........
a) C2A
b) C3A✔️
c) C2S
d) C3S
8).sand is suitable for concrete work is......
a) Fine sand
b) coarse sand
c) Graded sand✔️
d) medium sand
9).sand is suitable for masonary and plaster work is......
a) Fine sand✔️
b) coarse sand
c) graded sand
d) medium sand
10).Nearly Liter of water per bag of cement is required.......
a) 25
b) 28✔️
c) 30
d) 35
11).To gain better strength such sand is considered suitable for preparing mortar....
a) Coarse sand
b) Graded sand✔️
c) fine sand
d) medium sand
12).Minimum period of curing the ordinary concrete in days..
a) 14✔️
b) 10
c) 7
d) 2
13).Expansion joint in Rcc slab/Road provide after......in a length
a) 20 m✔️
b) 25 m
c) 30 m
d) 35 m
14).Red hematite is an ore of....
a) iron✔️
b) copper
c) aluminium
d) Lead
15).Galena is an ore of....
a) iron
b) copper
c) aluminium
d) Lead✔️
16).Destemper is used on..
a) iron
b) wood
c) brick masonry✔️
d) all of these
17).The chief ingredient of paint is...
a) base
b) inert filler
c) pigment✔️
d) drier
18).The glass scrap used in manufacturing of glass is termed as...
a) broken glass
b) mirror
c) face glass
d) cullet✔️
19).The residual material of petrolium used for road making and other purposes is termed as....
a) asphalt
b) bitumen✔️
c) crude petrolium
d) slag
20).The raw material manufacturing of glass is...
a) silica
b) lime
c) potash
d) all of these✔️
21).A material composed of two or more material performing batter while its constituents can be identified....
a) Hi tech
b) Composite✔️
c) Hi profile
d) Compatible
22).which material is used as binder in composite material....
a) polyster
b) expoxy
c) bitumen
d) All of these✔️
23).Material used for heat insulation of building...
a) thermocol
b) woodwool
c) glass wool
d) all of these✔️
24).....is a white powder used as ornamental work
a) plaster of paris✔️
b) ebonite
c) linolium
d) all of these
25).The floor provided below the ground level is called....
a) Ground floor
b) first floor
c) lower floor
d) basement floor✔️
25).A horizontal building placed to cover the opening of door and window is termed as..
a) Lintel✔️
b) beam
c) slab
d) column
26).Ratio between ultimate and safe bearing capacity of soil is termed as....
a) Bearing ratio
b) safe ratio
c) factor of safety✔️
d) safe ultimate ratio
27).when two or more footing are connecting by a beam is called...
a) combined footing✔️
b) raft/mat footing
c) stepped footing
d) none
28).The most important tool in brick laying for lifting and spreading mortar is....
a) float
b) brick axe
c) trowel✔️
d) showel
29).The depression provided in the face of a brick is called....
a) boat
b) trade mark
c) prism
d) frog✔️
30).Thickness of D.P.C layer of concrete (1:2:4)
a) 2"
b) 3'
c) 1.5"✔️
d) 1"
31).The cavity wall is generally provided for
a) preventing dampness
b) heat insulating
c) sound insulating
d) all of these✔️
32).The wedge shape blocks used to construct the arch is called....
a) skew back
b) key
c) crown
d) voussoirs✔️
33).Arches are made in hollow blocks masonary.
a) single
b) double
c) hollow
d) solid✔️
34).Load bearing walls are generally provided with...
a) foundation✔️
b) super structure
c) column
d) beam
35).A partition wall may be....
a) folding
b) collapsible
c) fixed
d) all of these✔️
36).sky light is a type of..
a) door
b) window✔️
c) c.window
d) all of these
37).Vertical or horizontal thin member which is used to divide the leaf of glazed door.....
a) rebate
b) rail
c) sash bar✔️
d) style
38).The roof which slopes in two direction...
a) mansard
b) hipped
c) gambral✔️
d) none
39).The roof which slopes in four direction...
a) hipped✔️
b) gambral
c) gable
d) all of these
40).Making the surface rough before finishing the surface is termed as
a) back ground
b) randering
c) doubing
d) hacking✔️
41).Filling the cavities with mortar before plastering is termed as....
a) back ground
b) randering
c) doubing✔️
d) none of these
42).Bamboo is an example of such trees...
a) conifer
b) endogenous✔️
c) veneer
d) pith
43).The age of a tree can be known by examining..
a) stem
b) leaf
c) annual ring✔️
d) bark
44).Vertical members of scafolding are...
a) putlogs
b) braces
c) ledgers
d) standards✔️
45).The temporary support to a structure undergoing alteration is called....
a) under pining✔️
b) dead shoring
c) flying shoring
d) raking shoring
46).A horizontal structural member of building which divide the building in different stories is termed as...
a) Roof
b) Ceiling
c) Floor✔️
d) Beam
47).Foundation whose depth is equal to its width will be called...
a) Shallow foundation✔️
b) Deep foundation
c) Well foundation
d) Any one
48).A shallow foundation suitable for multistoried building in ordinary soil is.......
a) Spread foundation
b) Stepped foundation
c) Raft foundation✔️
d) Grillage foundation
49).For ordinary soil factor of safety for bearing capacity is taken as.....
a) 1-3
b) 3-5✔️
c) 4-7
d) 5-7
50).Method of improving bearing capacity of soil
a) Stabilization
b) Compacting
c) Rolling
d) All of these✔️
51).Removing of water from foundation of building is called...
a) Escaping
b) Watering
c) Dewatering✔️
d) Sinking
52).The pile which transfer the load by means of skin friction along their length are known as.....
a) Friction pile✔️
b) Sand pile
c) Steel pile
d) Disc pile
53).Number of bricks required for one cubic meter of brick masonry.
a) 400
b) 500✔️
c) 600
d) 700
54).The stretcher bond in brick masonry can be used only when the thickness of wall
a) 10 c.m (4.5")✔️
b) 20 c.m (9")
c) 30 c.m (12")
d) 40 c.m ( 16.5")
55).When a brick is cut half,length wise then the cut bricks are known as..
a) Queen closer✔️
b) King closer
c) Bat
d) All of these
56).Which bond is strongest in brick masonry...
a) Header bond
b) English bond✔️
c) Flemish bond
d) Stretcher bond
57).Best bonding for stone masonry is considered.....
a) English
b) Flemish✔️
c) Dutch
d) Hare bone
58).The stone masonry made of properly dressed stone is known..
a) Ashlar ✔️
b) Rubble
c) Random
d) None of these
59).The modified from of english bond is called....
a) Dutch✔️
b) Flemish
c) Raking
d) Header
60).In stone masonry a stone having length equal to full width of the wall is termed as...
a) Big stone
b) Central stone
c) Through stone✔️
d) Key stone
61).A layer of stone having groove out side the room to prevent rain water to enter the wall is termed as....
a) Carbel
b) Cornice
c) Drip stone✔️
d) Rubble stone
62).A stone projected inside the room to support the beam is termed as....
a) Carbel✔️
b) Cornice
c) Drip stone
d) Rubble stone
63).The groove provided at bottom of drip stone..
a) Drip course
b) Template
c) Throating✔️
d) None of these
64).The pe*******on of water content inside a building is known as...
a) Dampness✔️
b) Salinity
c) Increases
d) All of these
65).For heat and sound proofing such walls are considered suitable...
a) Non load bearing wall
b) Load bearing wall
c) Hollow wall✔️
d) Retaining wall
66).Arches are made in hollow block masonry..
a) Hollow
b) Solid✔️
c) Single
d) Double
67).Masonry walls should be cured for..days
a) 3
b) 8✔️
c) 10
d) 14
68).Cement plaster cured
a) 7
b) 10✔️
c) 15
d) 21
69).Ordinary concrete work cured.....
a) 7
b) 14✔️
c) 21
d) 28
70).Inner curve of an arch is called...
a) Haunch
b) Intrados✔️
c) Extrados
d) Soffit
71).Under side/surface of the arch is called..
a) Haunch
b) Intrados
c) Extrados
d) Soffit✔️
72).The highest point on extrados of an arch is called....
a) Skew back
b) Key
c) Crown✔️
d) Voussoirs
73).The surface of the abutment on which the arch rests is known as...
a) Skew back✔️
b) Key
c) Crown
d) Voussoirs
74).Central big size wedge shaped block of an arch is termed as....
a) Skew back
b) Key✔️
c) Crown
d) Voussoirs
75).The points where an arch starts are called..
a) Skew point
b) Springing point✔️
c) First point
d) All of these
76) The portion below the line joining crowns of consecutive arches is called ..
a) Spandral✔️
b) Haunch
c) Crown
d) Extrados
77).The lower half portion of the extrados between skewback and the crown is called...
a) Haunch✔️
b) Spandral
c) Springer
d) Rise
78).The vertical member of the frame of door are called....
a) Head
b) Post✔️
c) Styles
d) Sills
79).The vertical outer member of the shutter of door is called...
a) Head
b) Post
c) Styles✔️
d) Sills
80).Vertical member dividing the door or window in portions is called....
a) Transom
b) Mullion✔️
c) Post
d) Style
81).The window which projects outside the room of a building is called....
a) Bay window✔️
b) Dormer window
c) Lantern window
d) None of these
82).A window fixed at vertical triangular portion of wall under slopy roofs is called....
a) Dormer window✔️
b) Bay window
c) Lantern window
d) None of these
83).A window fixed at flat roof is called window...
a) Lantern window✔️
b) Bay window
c) Dormer window
d) None of these
84).The projection of the head of a door or window frame embeded in the masonry are called...
a) Post
b) Frame
c) Horns✔️
d) Style
85).A horizontal member used to support the common rafter of truss..
a) Purlin✔️
b) Principal rafter
c) Common rafter
d) Queen post
86).Purlin are member which are laid horizontally to support....when span of the truss is large.
a) Common rafter✔️
b) Principal rafter
c) Purlin
d) Queen post
87).Vertical triangular portion of wall under the sloping roof....
a) Gable ✔️
b) Gambral
c) Hut
d) Pitch
88).The lower edge of sloping roof is termed as
a) Ridge
b) Valley
c) Eave✔️
d) Node
89).Scratching of old plaster or paint is called
a) Hacking
b) Peeling✔️
c) Dubbing
d) Randering
90).Thickness of single layer of plaster is kept..mm thick
a) 24mm (1")
b) 12mm (1/2")✔️
c) 36mm (1.5")
d) 48mm (2")
91).A first class brick should not absorb water more than,its weight..
a) 10%
b) 15%
c) 20%✔️
d) 25%
92).After one day's immersion,good stone absorb water not more than % of its own weight.
a) 5
b) 10✔️
c) 15
d) 20
93).Cutting of stone to required shape and size before its use is termed as....
a) Dressing✔️
b) Burning
c) Blasting
d) Wedging
94).Rich lime/High calcium lime is also called as...
a) Fat✔️
b) Hydraulic
c) Slacked
d) All of these
95).For common purposes the cement is used...
a) Natural cement
b) Ordinary port land cement✔️
c) Quick setting cement
d) None of these
96).When dry sand is moistured,it increases its volume this is called...
a) Slacking
b) Washing
c) Bulking✔️
d) Dampness
97).The process of making the back ground rough to act as key for plastering....
a) Hacking✔️
b) Dubbing
c) Peeling
d) Priming
98).Sand is used in mortars to reduce.....of the binding material.
a) Volume
b) Strength
c) Shrinkage✔️
d) All of these
99).The process of proper and accurate measurment of all concrete ingredients for proportioning is termed as....
a) Mixing
b) Placing
c) Transportation
d) Batching✔️
100).The strength of cement concrete for a given mix depends upon.
a) Water cement ratio✔️
b) Initial setting time
c) Final setting time
d) None of these
101).The process of keeping concrete wet to enable it to attain full strength is known as...
a) Curing✔️
b) Misting
c) Wetting
d) Quenching
102).Concrete from which elements are casted before their use...
a) Pre-cast✔️
b) Pre-stressed
c) Cast in situ
d) Rcc
103).Concrete elements casted at site at their place are termed as...
a) Ore cast
b) Pre stressed
c) Cast in situ✔️
d) Rcc
104).Melting the calcinated ores along with flux is called...
a) Querying
b) Smelting✔️
c) Metallergy
d) Dressing
105).Black jack is an ore of.....
a) Lead
b) Zinc✔️
c) Aluminium
d) Iron
106).Bauxite is an ore of..
a) Lead
b) Zinc
c) Aluminium✔️
d) Iron
107).A transperent solution containing rasin and oil which is used for finishing purposes is called....
a) Enamel
b) Emulsion
c) Weather sheet
d) Varnish✔️
108).White lead and red lead are used in the paints as...
a) Base ✔️
b) pigment
c) Drier
d) Solvent
109).The liquid part of the paint is called....
a) Solvent✔️
b) Base
c) Pigment
d) Drier
110).The ingredient which provide colour to the paint is called....
a) Pigment✔️
b) Base
c) Solvent
d) All of these
111).A concrete reinforced with fiber instead of steel is termed as....
a) High strength concrete
b) Fiber reinforced concrete✔️
c) Mass concrete
d) Special concrete
112).Which is composite material....
a) Plywood
b) Concrete
c) Fiber glass
d) All of these✔️
113).A material used to join two or more material s....
a) Resin
b) Glue
c) Adhessives
d) All of these✔️
114).Fire bricks can resist the temperature upto......
a) 500 C
b) 1000 C
c) 1500 C
d) 2000 C✔️
115).Raw umber is used in the paint to get the colour......
a) blue
b) red
c) grey✔️
d) green
116).The main function of alumina in brick earth is to impart.......
a) Plasticity✔️
b) Increasing volume
c) Colour
d) Strength
117).The following ingredient exclude in white cement.......
a) iron oxide✔️
b) tri calcium
c) alumina
d) silica
118). The slump test of concrete is used to measure its.........
a) workability strength✔️
b) pre stressed
c) Batching
d) mixing
119). When a heavy structure is to be constructed in sandy soil the foundation used as...
a) Pier foundation✔️
b) strap foundation
c) Raft foundation
d) none of these
120).Raft foundation is also known as.......
a) pile foundation
b) pier foundation
c) Cantilever foundation
d) Mat foundation✔️
121).A horizontal layer of bricks laid in mortar is known as.........
a) Course✔️
b) Stretcher
c) header
d) closer
122).The minimum bearing of lintel on door or window is kept........
a) 100mm (4")
b) 150mm (6")✔️
c) 200mm (8")
d) 250mm (10")
123).An inclined member of a roof truss........
a) Rafter✔️
b) purlin
c) cleat
d) none of these
124).The best type of pointing in ordinary cases........
a) Flush pointing✔️
b) deep struck pointing
c) tuck pointing
d) recessed pointing
125).The temporary support provided to an unsafe structure is called...........
a) Shoring✔️
b) under pining
c) proping
d) timbering
Gooooood Luckkkkkk
14/07/2021
10/07/2021
18/05/2021
Mostly PPSc Urdu Portion
03/05/2021
Which of the following is the unit of kinematic viscosity _________________?
0
A. pascal
B. poise
C. stoke
D. faraday
E. none of the above
Ans(C)
03/05/2021
Density of water is maximum at ___________________?
0
A. 0°C
B. 0°K
C. 4°C
D. 100°C
E. 20°C.
Ans(D)
03/05/2021
Cross staff is an instrument used for________________?
0
A. measuring approximate horizontal angles
B. setting out right angles
C. measuring bearings of the lines
D. none of the above
Ans(B)
Click here to claim your Sponsored Listing.
Category
Contact the school
Telephone
Website
Address
Multan