Autobunkerz

Mechatronics Dq200 All repaired and ready to go 😄

ECU work today

🔧 BMW MSV90 ECU REPAIR SPECIALISTS – BRISBANE 🔧
Having engine management issues on your BMW?
At Autobunkerz Brisbane, we specialise in BMW MSV90 ECU diagnostics, testing, cloning and repair. Many MSV90 control units suffer from internal electronic failures that can cause misfires, no-start conditions, communication faults and injector control issues.
✅ BMW MSV90 ECU Repair
✅ ECU Cloning & Data Transfer
✅ Injector Driver Circuit Repair
✅ No Start Diagnosis
✅ Communication Fault Repair
✅ Water Damage Repair
✅ Bench Testing Available
✅ Programming & Coding Support
✅ Workshop-to-Workshop Service
Common Symptoms: ▪️ Engine Cranks But Won't Start
▪️ Multiple Cylinder Misfires
▪️ Injector Faults
▪️ No Communication With ECU
▪️ Check Engine Light On
▪️ Intermittent Starting Problems
▪️ Power Loss & Limp Mode
Common Fault Codes: ▪️ 2A82 – VANOS Intake Fault
▪️ 2A87 – VANOS Exhaust Fault
▪️ 29CD – Misfire Cylinder 1
▪️ 29CE – Misfire Cylinder 2
▪️ 29CF – Misfire Cylinder 3
▪️ 29D0 – Misfire Cylinder 4
▪️ 29D1 – Misfire Cylinder 5
▪️ 29D2 – Misfire Cylinder 6
▪️ 2F44 – EWS Preventing Manipulation
▪️ A0B4 – CAS Engine Start Fault
If your BMW has already had coils, plugs, sensors or wiring checked and the fault keeps returning, the ECU may require professional testing and repair.
📍 Brisbane ECU Repair Specialists
📍 European Vehicle Electronics Specialists
📍 Advanced Diagnostics & Module Repair

BMW MSV90 ECU testing, repair, cloning and programming available in Brisbane.

2019 BMW fuel pressure sensor leaking.. DME got full of fuel.

Don't worry I have solution.

Contact message Neil

0478837707

Yes! Another ECU repair reviews! Thank you !

🔧 DSG MECHATRONICS PCB REPAIR – BRISBANE 🔧

Microchips are getting harder to source and replacement mechatronic units are becoming more expensive every year.

Before replacing the entire unit, have the electronics properly diagnosed.

At Autobunkerz, we specialise in DSG, S-Tronic and PDK mechatronics repairs, including PCB-level diagnostics and component repairs.

✅ DQ200, DQ250, DQ381, DQ500 & DL501
✅ PCB-level electronic repairs
✅ Solenoid driver circuit repairs
✅ Sensor circuit repairs
✅ CAN communication faults
✅ No communication faults
✅ Water damaged mechatronics
✅ Bench testing available
✅ Coding & programming support
✅ Refurbished and replacement units available

Common Fault Codes:
▪️ P1735 – Clutch 1 Position Sensor Electrical Fault
▪️ P1736 – Clutch 2 Position Sensor Electrical Fault
▪️ P0606 – Internal Control Module Fault
▪️ U0101 – Lost Communication With TCM
▪️ P0841 – Hydraulic Pressure Sensor Fault
▪️ P17BF – Hydraulic Pump Protection
▪️ P189C – Pressure Drop Detected
▪️ P175E / P176F – Clutch Adaptation Limit Reached

Modern transmissions are electronic systems. In many cases, a component-level repair can save a perfectly good mechatronic unit from being replaced.

📍 Brisbane
🔧 Workshop-to-workshop support available

I20 ECU repaired in a house 😄

DQ200 Repaired for other workshop😄

Do some another work done to it.

Same airbag module for Golf.
last week and this week. three moduels failed

I have solution. Please contact me. Don't pay full price at dealer 😅